how to make an armchair cover

Posted on November 11, 2020 by

Remove the covers, leaving the pins in place, and loosely baste the edges together in long stitches with needle and thread. For tips on how to sew a slipcover for an armchair, read on! You will need one piece that is about 4 inches shorter than the width of the chair, and two that are each 4 inches shorter than the depth of the seat from front to back. Written by: Kimberly Napier. Remove the straight pins, but leave the safety pin marking the center front. Sew straight seams along all four edges of the fabric, removing the straight pins as you go. Sew the ties to the fabric, and remove the straight pins. Last Updated: March 29, 2019 Purchase enough canvas or upholstery fabric to completely cover the chair. Stitch the edges together, using a sewing machine. Measure your chair from the floor in front of it up and over the seat and then up and over the back to the floor behind it. Pin the overlapping edges of fabric together with upholstery pins every inch or two along the seams. Make sure to cut them bigger than the actual measure, especially the pieces for the arms, they must be much larger than how they actually are. Fold all four edges under 1/4 inch, and press the folds flat with an iron. This project calls for … You could even add a decorative pin over the knot, if desired. Hand stitch the open edges closed. Slipcover fabric can be anything from 6-ounce twills to 12-ounce canvas. Purchase enough canvas or upholstery fabric to completely cover the chair. Place the fabric over your chair with the printed side up. Cut three pieces of heavy cardboard tubing (like fabric comes on) or PVC pipe no more than about 1 or 2 inches inches in diameter. She has also been knitting and crocheting for more than 40 years. Turn the edges of the fabric up another 3/4 inch or so, and pin the folds in place. Start at the safety pin, and work your way around the chair, pinning up the hem. When pinning the cushions, leave one edge free so you can remove and replace the cover later. Remove the cover from the chair, and sew the hem in place. How to Upholster a Footstool With Nail Heads, How to Keep Cushions From Sliding Off Chairs, How to Make a Full-Skirted Dining Chair Cover. Add at least 1 inch (2.5 cm) to each measurement (the width and the total length) to ensure you have enough fabric to cover the entire chair. Choose good-quality sheets so the slipcover you make from them lasts. For slipcovers that will see heavy use, construct them with fabric that weighs 8 ounces per yard, and use a denim or size 16 needle on your sewing machine. Label each piece of the pattern so you don’t get confused later on. wikiHow's. Remove the pins. Replace the cover on the chair, and tuck the fabric as before. Knit 5 stitches, then knit 2, purl 2 across the remaining stitches until the last 5 stitches. This will help keep the fabric in place. Slipcovers are one of the quickest and simplest ways to give an old chair a new look. Knit the remaining 5 stitches. If the cushions aren’t removable, skip this step. Make ties out of leftover fabric to save a few dollars and achieve a cleaner, more tailored effect. Feel free to wash and iron the pillowcases before using them. Use straight pins to attach ties at the front of the arms and the rear corners for a more tailored fit. Cut one long piece of fabric according to your measurements. How to Change the Fabric on an Office Chair. How to Make Simple Chair Covers. © Copyright 2020 Hearst Communications, Inc. Pre-shrink your fabric before you begin cutting and sewing it. How to make protective arm covers for a chair, quickly and easily.By William MacDonaldhttp://www.upholsterycourse.com Gather the fabric in pleats or soft folds at the front of the arms and the rear corners of the chair, and secure the fabric with the ties. A running enthusiast who regularly participates in San Francisco's Bay to Breakers run, Chandler works as an independent caterer, preparing healthy, nutritious meals for Phoenix area residents. For tips on how to sew a slipcover for an armchair, read on! To save the wear and tear on armchairs, it is often helpful to create covers … Measure from the floor on the left side of the chair up and over the arm, across the seat and up over the other arm to the floor on the right side of the chair. Next, remove the seat cushion, and cut a pillow case 4 inches larger than the cushion on all sides so you can wrap it around the bottom of the chair. Find the widest part of your chair, whether that is the space between the front legs at the bottom or the seat at its widest part. Make Pillowcase Chair Covers for a Wedding. Add 2 inches to get the total width of fabric you need for the cover. Next, remove the seat cushion, and cut a pillow case 4 inches larger than the cushion on all sides so you can wrap it around the bottom of the chair. These can be made using a variety of stitches or by a simple garter stitch. Sew on the ties, using one 12-inch piece of cording or ribbon per tie. There are 22 references cited in this article, which can be found at the bottom of the page. Press the folds flat. Include your email address to get a message when this question is answered. Add 10 inches to get the length of fabric you will need for your cover. Remove the armchair’s cushions and measure their length, width and height. If you’re using printed fabric, make sure the pattern matches up in a way you like. We use cookies to make wikiHow great. Fit the fabric around the chair and its cushions, wrong-side-out, leaving 2 inches free on each edge. You will have to move the pins holding the front and back together to finish the folds in that area. Cut a big (huge :D) piece of fabric that will cover the whole back, including the central back/leg piece, and 2 smaller pieces to cover the back of the arms. To make a chair cover, start by selecting 2 matching pillow cases, one for the back of the chair and the other for the cushion. Purchase enough canvas or upholstery fabric to completely cover the chair. Fabric and home stores often sell pre-made armchair covers in a variety of sizes, colors and fabrics, but you can save money sewing your own. Pin a 12-inch cord or piece of ribbon to the front and back of the fabric where the seat meets the back on each side. This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. Using Pillowcases to Cover Dining Room Chairs, {"smallUrl":"https:\/\/www.wikihow.com\/images\/thumb\/5\/58\/Make-a-Chair-Cover-Step-01.jpg\/v4-460px-Make-a-Chair-Cover-Step-01.jpg","bigUrl":"\/images\/thumb\/5\/58\/Make-a-Chair-Cover-Step-01.jpg\/aid1355828-v4-728px-Make-a-Chair-Cover-Step-01.jpg","smallWidth":460,"smallHeight":345,"bigWidth":"728","bigHeight":"546","licensing":"

how to make an armchair cover

Leave a Reply Cancel reply